17.
18.
like this, with the top of the
triangular section going
under the horizontal edge
immediately above,
until you get this.
Watch your position, now.
Valley fold twice as shown,
crease firmly, and unfold.
Repeat Step 19 at the
illustrated location.
20.
1st Square
2nd Square 3rd Square 4th Square
19.
1st Square
2nd Square 3rd Square 4th Square
21.
22.
23.
25.
Open out,
and make three more
crease lines as shown.
Collapse along the existing
crease lines as illustrated,
and like this. The paper on
the upper half of the
zigzagging, mountain fold
line a-b is to be folded 90
degrees to the back of the
rest of the paper.
Valley fold the two tabs in
the middle to each side.
26.
Turn over
24.
a. b.
then squash fold, with
three with three layers on
each side.
27.
32.
31.
28.
29.
Swivel the broad flap on the
right and the narrower piece
immediately behind it to the
left,
30.
then swivel the narrower piece
to the right, freeing it from the
triangular layer above,
like this, before swivelling the
broader piece back to the right.
Now swivel the broad flap on
the left and the narrower piece
immediately behind it to the
right, and repeat Steps 29 and
30 on this side.
Valley fold each of the vertical
edges to the centre, crease firmly,
and unfold.
34.
35.
33.
a.
b.
c.
Now bring the corners b and
c to the the apex at a,
then separate the
layers and squash
fold,
like this. Turn paper over.
36.
37.
38.
39.
40.
41.
42.
43.
Reverse fold.
Fold and unfold at the top,
creasing firmly.
The diamond shaped piece
in the middle will be used to
form the head. Valley fold both
sides as shown.
Squash fold both sides,
then valley fold all layers as
shown, crease firmly, and
unfold.
Hold the circled area firmly
and pull to each side to
open out the pleated layers.
Valley fold as shown, along the
crease lines made in Steps 38
and 39.
Pleat fold both sides to
close up again.
Now for the head
Valley fold both sides
again as illustrated.
44.
47.
46.
45.
48.
49. 50.
51.
52. 53.
Open up and flatten the
pleated layers.
Swivel the left half of the head
piece to the right,
then stick a finger in
between the layers
from beneath, all the
way to the corner,
and do a closed double sink;
i.e. mountain fold both layers
along the inner crease line,
and valley folding the same
layers along the outer crease
lines.
Swivel the piece left on
completion of Step 48,
and repeat Steps 47 to 49
on the right side of the head.
Turn over.
Fold and unfold as shown,
creasing the layer nearest
to you only.
Now bring the intersecting
point of the mountain fold - of
the first layer only - downwards
by pushing in the sides as
shown,
54.
55.
57.
58.
59.
while bringing down the whole
of the upper section,
like this.
Now valley fold between the
circled landmarks, crease
firmly, and unfold.
Valley fold the lower section
and twice at the top.
56.
Now valley fold the left corner
under the layer directly above it.
This is an enlarged view of the
top section. Reverse fold as
shown.
The two pointed pieces will
be the fangs. Mountain fold
to hide the excess paper.
60.
Draw the fangs slightly together, with
each positioned about 90 degrees
from the rest of the paper.
Valley fold,
61.
62.
63.
64.
65.
67.
Unfold, do a closed sink,
and repeat Steps 56, 57,
61 to 63 on the right.
Rabbits ear fold as
shown on both
pieces tp form the
forked tongue.
Fold the edges of each side to
stand at 90 degrees to the folding
surface.
Valley fold up, slightly below the
existing crease line as shown in the
diagram.
66.
69.
68.
Mountain both corners into the pockets
on each side of the the triangular tab
underneath,
Lift the headpiece and slot its triangular
base into the pocket underneath as
illustrated, to lock the jaws neatly in place.
70
.
This is how the king cobra should look at this
stage.
Turn paper over.
like this. Make a little crimp in the
centre of the eyeball and gently press
the layers at the front and back of the
eyeball together.
Note:
The eyeball may flatten as folding
progresses. Wetfolding helps keep it
rounded. A little ball of cotton inserted
(shhh ) behind the eyeball also
helps.
71.
73.
Swivel the left half of the headpiece
to the right,
then stick a finger under the first layer
as illustrated, all the way to round out
the eye on this side,
74.
72.
Swivel one flap to the left and repeat
Steps 71 to 73 on the right.
Mountain fold the excess corners of the
head uderneath as shown. Crease the
folded edges firmly.
75.
76.
77.
78.
3rd Square 4th Square
Mountain fold both sides as shown to
hold the layer with the eyes down.
Turn over
Pleat fold as shown, dividing each square
area horizontally into 1/16ths.
79.
3rd Square 4th Square
80.
Now do a series of crimp folds. The space between each
vally and mountain fold should be 1/32 of the the height
of each square area.
Now comes the tricky bit.
Hold the crimp folded areas together and collapse
the model along the existing crease lines on the
fifthe square like this,
Không có nhận xét nào:
Đăng nhận xét